Vehicles
90 not categorized PORSCHE 914 OIL SEALCan't find what you need? Try browsing the Accessories or Exploded Diagrams!<-- Try narrowing by car using the menu to the left.T55100204 Oil seal installer, flywheel end. Specially manufactured to our specifications, these tools make it easy to properly install the rear crankshaft seal. They fully support, position and press the fragile oil seal into place without distortion. For all 356 engines.
$82.45
Make a selection 021115487 Cork gasket that fits inbetween the oil filler and the engine case on all 914 four cylinder models. critical on 1.8 models to help seal vacuum leaks as well as oil leaks. View/Change Diagram
From $2.90
Make a selection 021101173 2 required View/Change Diagram
$5.46
Make a selection 021119955 This is another one of those small sealing washers to insure that all of the cooling air is flowing over the engine and not out the open holes! order all of the other sealing washers at the same time like the spark plugs and the oil pressure switch grommet. View/Change Diagram
$5.25
Make a selection 021119957 This is an autoatlanta exclusive oil pressure switch boot for all 914-4 models. believe it or not your 914 had this factory installed. long gone on most engines by now this part is critical to seal in the cooling air. easily installed, this part fits behind the distributor. please check the oil pressure switch for leaks at the same time. View/Change Diagram
$13.00
Make a selection 90110511503 Valve covers finish off the engine but often warp or wear out over time. Replace warn-out, leaky valve covers before the oil catches your car on fire! These new covers fit perfectly and ensure a good seal. Make sure you use new gaskets when installing them. View/Change Diagram
$398.13
Make a selection 91431802901 If your speedometer completely fails look at the angle drive first before suspecting the cable. easily checked by disconnecting the speedometer cable then lifting the car and putting it in gear to see if the angle drive spins, the part is easily replaced. always try to buy a new one as this is a wear part. purchase a speedo angle drive seal at the same time to stop the transmission fluid leak. it fits on the drive gear in the rear tail cover and is easily removed with the rear 13mm headed set screw. (you will have a fluid spill when this is removed so get ready!) refill with 80/90 weight oil only. View/Change Diagram
From $52.47
Make a selection MS4E Our major service kit consists of everything we use when performing a thorough 914 major service. Don’t be caught short of parts when you do yours! Fuel filter, oil filter, strainer kit, alternator belt, spark plugs, points, distributor cap, distributor rotor, valve cover gasket kit, oil cap seals (1.8), distributor o-ring, condenser, oil drain plug washer. Please specify year and engine size when ordering. General Fitment914 1970-76
$113.33
Make a selection 91411600002 Our 18-piece clutch package contains everything we use in our shop for a perfect clutch replacement. beware of lesser kits, you will need all of these parts! Included is the clutch installation manual. Kit includes: rear main seal, throwout bearing, 2 throwout bearing clips, flywheel, front trans. Seal, 2 cv joint gaskets, flywheel o-ring, ball stud cup, 2 muffler gaskets, needle bearing, cv joint bolt, clutch alignment tool, flywheel crush washer, felt washer, pressure plate, clutch disc, clutch installation manual. General Fitment914 1970-76
$917.39
Make a selection MS4L Our major service kit consists of everything we use when performing a thorough 914 major service. Don’t be caught short of parts when you do yours! Air filter, fuel filter, oil filter, strainer kit, alternator belt, spark plugs, points, distributor cap, distributor rotor, valve cover gasket kit, oil cap seals (1.8), distributor o-ring, condenser, oil drain plug washer. Please specify year and engine size when ordering. General Fitment914 1970-76
$196.58
Make a selection 91411600001 Our 18-piece clutch package contains everything we use in our shop for a perfect clutch replacement. beware of lesser kits, you will need all of these parts! Included is the clutch installation manual. Kit includes: rear main seal, throwout bearing, 2 throwout bearing clips, flywheel, front trans. Seal, 2 cv joint gaskets, flywheel o-ring, ball stud cup, 2 muffler gaskets, needle bearing, cv joint bolt, clutch alignment tool, flywheel crush washer, felt washer, pressure plate, clutch disc, clutch installation manual. General Fitment914 1970-76
$917.39
Make a selection 022115315 Oil cap seal for the 912e and the 1.8 l equipped 914 made from 1974-76. Viton material. View/Change Diagram
$7.10
Make a selection 10010303204 - 3.2 l for increased horsepower and torque.* - genuine mahle forged pistons with deeper valve pockets. - genuine mahle steel (st52) nikasil coated cylinders.** - piston pin bore is off center (deaxiated) for factory quiet operation. - 10.3:1 compression. - 98 mm big bore. - 22x58 racing wrist pins - 70.4 stroke. - made in Germany by mahle gmbh. - piston rings installed directly on the pistons for ease of installation. - complete set with cylinders, pistons, rings, wrist pins and clips. - kit weighs 21.03 lbs. (9.54 kg). Mahle pistons are forged for substantially higher and more uniform strength over pistons that are cast. Mahle cylinders are manufactured from st52 steel which has extremely high thermal resista...(choose a part on the right to read more)
$9,693.51
Make a selection 117021356 Engine oil cooler. High performance version. Provides better heat transfer and improved cooling. Includes hardware, seals, and instructions. General Fitment356 1950-59356 1960-65 912 1965-69
$725.93
Make a selection 100505965 With front and rear steel fender flares including lights (front and rear head / tail and fog lights, blinkers), side skirts, installation hardware (all seals, gaskets, screws washers, nuts), cup mirrors and accessories. Without rear spoiler. General Fitment911 1970-73
$11,088.46
Make a selection 100103038TU997 Mahle 3.8 liter piston and cylinder conversion kit for 996/997 turbo / GT2 & GT2 rs - increased horsepower and torque.* - forged pistons with deeper, mirrored valve pockets with 23 mm wrist pin. - slip fit, steel (st52) cylinders. - piston pin bore is off center (deaxiert) for factory quiet operation. - 9.4:1 compression. - 102 mm bore. - piston rings installed directly on the pistons for ease of installation. - made in Germany by mahle gmbh. *please note: horsepower and torque gains depend on the software used, camshafts, crankshaft and other internal modifications. 700+ hp and torque can be achieved with use of these pistons and cylinders with a proper engine build and software. Contact your sales person for ...(choose a part on the right to read more) General Fitment911 TURBO/GT2 2001-05911 TURBO/GT2 2007-09
$14,654.60
Make a selection 106084 There are not many warning signs of an impending ims failure short of a “death rattle” that occurs as the bearing fails and comes apart. These kits replace the factory sealed bearing with a new, severe duty custom ceramic hybrid roller ball bearing for reduced friction and superior performance in poorly lubricated operating conditions and replaces the factory ims flange hub, bearing support, and fastener with a stronger, revised billet chromoly assembly. The center bearing support also receives an increase in size and no longer is cut for the o-ring that keep engine oil from leaking out of the engine - we have relocated the o-ring to the ims hub flange for added strength to the center stud & bearing support...(choose a part on the right to read more) General FitmentBOXSTER 2005-08BOXSTER 1997-04 911 1998-05 911 1987-89
$899.99
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |